Difference between revisions of "Audio capture"

From User Manual :: Screenbits
Jump to: navigation, search
(Recording Devices)
(Supported formats)
Line 32: Line 32:
 
To change the default format of an audio device:
 
To change the default format of an audio device:
  
#Select '''Settings''' from ''Recording'' menu to open ''Settings'' view.
+
#Select '''Settings''' from ''Menu'' menu to open ''Settings''.
#From ''Input'' section under the ''Audio'' tab, click '''Configure''' to open sound settings.
+
#From ''Input'' section under the ''Audio'' tab, click '''Configure''' to open ''Sound'' control panel.
 
#Right click on name of the device in list under the ''Playback'' or ''Recording'' tab and click '''Properties'''.
 
#Right click on name of the device in list under the ''Playback'' or ''Recording'' tab and click '''Properties'''.
 
#From ''Default Format'' section under the ''Advanced Tab'' select one of the supported formats above.
 
#From ''Default Format'' section under the ''Advanced Tab'' select one of the supported formats above.

Revision as of 14:15, 23 May 2020

Audio Recording

You can record audio from any input or output device including microphone and speakers (system sound).

Figure 1: Output devices


Figure 1: Input devices


To enable recording an output device (e.g. Speakers or system sound):

  1. From the application window, under Audio section, click Output audio button to open output audio menu.
  2. Turn Record output audio switch on.
  3. Click Record button to start recording.


To enable recording an input device (e.g. Microphone):

  1. From the application window, under Audio section, click Input output button to open input audio menu.
  2. Turn Record input audio switch on.
  3. Click Record button to start recording.

Notes

  • You can select the device to record if you do not want to record the default device.
  • List of the devices may vary depending on your hardware.

Supported formats

Screenbits supports recording the following audio formats for the input:

  • 8kHz, 11.025kHz, 16kHz, 22.05kHz, 24kHz, 32kHz, 44.1kHz, 48kHz, 88.2kHz, 96kHz, 176.4kHz, 192kHz sample rates
  • 1 (mono), 2 (stereo), 4, 6 and 8 channels
  • 16, 24 and 32 bits per sample

If you attempt to record an audio device with an unsupported format, an error message pops up asking you to select a different format for the device.

To change the default format of an audio device:

  1. Select Settings from Menu menu to open Settings.
  2. From Input section under the Audio tab, click Configure to open Sound control panel.
  3. Right click on name of the device in list under the Playback or Recording tab and click Properties.
  4. From Default Format section under the Advanced Tab select one of the supported formats above.
  5. Click OK to apply changes to the device properties


Figure 2: Audio Format - Sound settings


Output format

Screenbits encodes recorded audio using AAC codec, allows you to configure bit-rate, sample-rate and number of channels for it.

To change format of the output audio:

  1. Select Settings from Record menu to open Settings dialog.
  2. Click Audio from the side bar to open Audio settings.
  3. From Output format section, select the desired bit-rate, sample-rate and number of channels for the output audio.

Note: If multiple audio sources are selected, Screenbits mixes both audio streams into a single audio track.

Performance

There are several ways to improve performance of Screenbits. If you want are experiencing glitches in the recorded audio or using Screenbits on a low-end device, follow one or more instructions on below to improve the performance.

Use default formats

If you record audio, select one of the following formats for the audio device from the Audio settings

  • 2 channel (stereo), 16bit, 44100 Hz
  • 2 channel (stereo), 16bit, 48000 Hz

Select the same format for multiple devices

If you record both recording and playback devices, make sure same format is selected for both devices. To make input and output match together to perform better, select Auto for sample-rate and channels from Audio settings.